Ten Common faults of impact Crusher and their Solutions

1、Impact crusher starting equipment not turning
 
Check if the material in front of the feeder falls into the broken cavity due to stop vibration, causing the material to jam the rotor. Need to clean up the material in the broken cavity and start up again.
 
2. Heat of impact crusher bearing
 
Check that the lubrication of the bearings is good, and that the lubricating oil should normally be filled with 50 percent of the bearing capacity; in another case, the lubricating oil is spoiled and thick, and the bearings need to be cleaned and new lubricating oil replaced.
 
3 Abnormal vibration of equipment
 
Possible causes and solutions are:
The size of the feed may be too large;
Wear is uneven, counterattack hammer needs to be replaced;
Rotor unbalance, need to be adjusted, proofreading balance;
Check that the equipment anchor bolts are fastened and properly strengthened.
 
4 Impact crusher belt flip
 
Mainly because of belt breakage, need to replace triangle belt, pay attention to ensure belt quality; or because of the improper assembly of pulley, we need to adjust the active, driven pulley in the same plane.
 
5 Bending or breaking of machine bearings
 
Main reasons include long-term overload operation of main engine, improper heat treatment of bearings, hardness of broken materials and so on. When processing, must replace the new bearing, and in the later operation process pay attention to maintenance and repair.
 
6 Impact crusher appear stuffy car
 
There are many reasons for the sudden shutdown of the impact crusher in operation, such as clogging of discharge opening, slip of belt, low voltage, bearing damage, and so on. These problems should be eliminated, such as removing clogs from discharge ports, tightening belts, increasing voltage and ensuring voltage stability, replacing bearings, etc.
 
7. Rupture of spring parts of equipment
 
The main reason for this failure is that the spring is not relaxed when adjusting the discharge port. Therefore, the broken spring must be replaced during treatment.
 
8 Internal abnormal noise of broken cavity
 
Stop immediately to check if metal impurities or parts are broken in the broken chamber and clean up the crusher cavity; check the fastening of the inner liner and the gap between the plate hammer and the liner, which can cause abnormal noise if the gap is too small.
 
9. The equipment has a taste of glue in operation
 
The main cause of this problem is belt slip, friction and heating with pulley to produce a harsh rubber smell, or the rotor is stuck, it is necessary to check the rotor in the machine cavity and solve it in time.
 
10. The size of discharge is too large.
 
It is shown that the plate hammer or counterattack liner of the counter-attack crusher is worn seriously, which causes the gap between the plate hammer and the counterattack plate to be too large, adjusts the clearance between the front and back counterattack frame, or replaces the lining plate and the plate hammer. Adjust the position of counterattack frame so that the gap between the two sides and the rack liner is even; if the liner on the rack is worn seriously, it should be replaced in time.

                    Click to view impact crusher parts introduction
 

Shuangfeng Qirun Machinery Parts IMP&EXP Co.,Ltd, specializing in the production of domestic and foreign brands of crusher wear spare parts manufacturers, production of domestic brands, Hua Yang, Shan Bao, SBM brands such as crusher wear parts, spare parts, as well as foreign brands, common, Sandvick, TEREX and other import brands crusher spare parts, wear parts, mining quarry companies such as crusher wear parts of choice. We achieve cost-effective localization of imported spare parts, service users at home and abroad. The company can be matched with various brands of hydraulic crusher electric parts, sealing parts, standard parts and other accessories, can meet the needs of one-stop shopping for customers at home and abroad the demand.
      
Shuangfeng Qirun Machinery Parts IMP&EXP Co.,Ltd has thirty years of production experience, and years of experience in processing export products, products have been exported to the United States, Canada, Australia, Sweden, Finland, Russia, Ukraine and Southeast Asia and other countries and regions. Shuangfeng Qirun Machinery Parts IMP&EXP Co.,Ltd product using the original material, high-quality raw materials, casting and heat treatment process we have a unique thirty years production experience, to ensure complete interchangeability, and original spare parts with high quality and competitive price, provide quality products, quality services for the majority of users.
 
Shuangfeng Qirun Machinery Parts IMP&EXP Co.,Ltd wearable parts can be customized to map, and if there is no map, the company has professional mapping personnel to help you mapping, after customization
 
Contact:Sales Director: Eileen Cai ;
      Email: sales@qrcrusher.com;
      Mobile telephone: +8618973821771